ObjectiveTo review the current research status of in situ three-dimensional (3-D) printing technique and future trends. MethodsRecent related literature about in situ 3-D printing technique was summarized, reviewed, and analyzed. ResultsBased on the cl inical need for surgical repair, in situ 3-D printing technique is in the preliminary study, mainly focuses on in situ dermal repair and bone and cartilage repair, and succeeds in experiments, but there are still a lot of problems for cl inical application. ConclusionWith the development of in situ 3-D printing technique, it will provide patients with real-time and in situ digital design and 3-D printing treatment with a timely and minimally invasive surgical repair process. It will be widely used in the future.
ObjectiveTo review the current progress of three-dimensional (3-D) printing technique in the clinical practice, its limitations and prospects. MethodsThe recent publications associated with the clinical application of 3-D printing technique in the field of surgery, especially in orthopaedics were extensively reviewed. ResultsCurrently, 3-D printing technique has been applied in orthopaedic surgery to aid diagnosis, make operative plans, and produce personalized prosthesis or implants. Conclusion3-D printing technique is a promising technique in clinical application.
ObjectiveTo construct large block of engineered liver tissue by co-culture of fibroblasts and hepatocytes on collagen hydrogels in vitro and do in vivo implantation research. MethodsSilastic mould was prepared using three-dimensional printing technology. The collagen hydrogel scaffold was prepared by collagen hydrogel gel in the silicone mould and was removed. Sprague Dawley rat lung fibroblasts were co-cultured with primary hepatocytes at a ratio of 0.4:1 on the collagen hydrogel scaffold to construct large block of engineered liver tissue in vitro (group B), and primary hepatocytes cultured on the collagen hydrogel scaffold served as control group (group A). The cell morphology was observed, and the liver function was tested at 1, 3, 7, 14, and 21 days after culture. The rat model (n=24) of hepatic cirrhosis was made by subcutaneous injection of carbon tetrachloride. And in vivo implantation study was carried in cirrhosis rat model. The phenotypic characteristics and functional expression of hepatocytes were evaluated at 3, 7, 14, 21, and 28 days after implantation. ResultsIn vitro results indicated that hepatocytes in group B exhibited compact polyhedral cells with round nuclei and high expression of liver function. Moreover, cells aggregated to the most at 7 days. Album production and urea synthesis incresed significantly when compared with group A (P<0.05). In vivo results showed hepatocytes in group B survived for 28 days, and albumin production and urea synthesis were significantly increased. In addition, hepatocytes showed an aggregated distribution and cord-like structures, which was similar to normal liver tissue. ConclusionThe large block of engineered liver tissue constructed by co-cultured cells can form tissue similar to normal liver tissue in vivo, and survive for a long time, laying foundations for building more complete engineered liver tissue in the future.
ObjectiveTo investigate whether subchondral bone microstructural parameters are related to cartilage repair during large osteochondral defect repairing based on three-dimensional (3-D) printing technique. MethodsBiomimetic biphasic osteochondral composite scaffolds were fabricated by using 3-D printing technique. The right trochlea critical sized defects (4.8 mm in diameter, 7.5 mm in depth) were created in 40 New Zealand white rabbits (aged 6 months, weighing 2.5-3.5 kg). Biomimetic biphasic osteochondral composite scaffolds were implanted into the defects in the experimental group (n=35), and no composite scaffolds implantation served as control group (n=5); the left side had no defect as sham-operation group. Animals of experimental and sham-operation groups were euthanized at 1, 2, 4, 8, 16, 24, and 52 weeks after operation, while animals of control group were sampled at 24 weeks. Subchondral bone microstructural parameters and cartilage repair were quantitatively analyzed using Micro-CT and Wayne scoring system. Correlation analysis and regression analysis were applied to reveal the relationship between subchondral bone parameters and cartilage repair. The subchondral bone parameters included bone volume fraction (BV/TV), bone surface area fraction (BSA/BV), trabecular thickness (Tb.Th), trabecular number (Tb.N), and trabecular spacing (Tb.Sp). ResultsIn the experimental group, articular cartilage repair was significantly improved at 52 weeks postoperatively, which was dominated by hyaline cartilage tissue, and tidal line formed. Wayne scores at 24 and 52 weeks were significantly higher than that at 16 weeks in the experimental group (P<0.05), but no significant difference was found between at 24 and 52 weeks (P>0.05); the scores of experimental group were significantly lower than those of sham-operation group at all time points (P<0.05). In the experimental group, new subchondral bone migrated from the surrounding defect to the centre, and subchondral bony plate formed at 24 and 52 weeks. The microstructural parameters of repaired subchondral bone followed a "twin peaks" like discipline to which BV/TV, BSA/BV, and Tb.N increased at 2 and 16 weeks, and then they returned to normal level. The Tb.Sp showed reversed discipline compared to the former 3 parameters, no significant change was found for Tb.Th during the repair process. Correlation analysis showed that BV/TV, BSA/BV, Tb.Th, Tb.N, and Tb.Sp were all related with gross appearance score and histology score of repaired cartilage. ConclusionSubchondral bone parameters are related with cartilage repair in critical size osteochondral repair in vivo. Microstructural parameters of repaired subchondral bone follow a "twin peaks" like discipline (osteoplasia-remodeling-osteoplasia-remodeling) to achieve reconstruction, 2nd week and 16th week are critical time points for subchondral bone functional restoration.
ObjectiveTo solve the fixation problem between ligament grafts and host bones in ligament reconstruction surgery by using ligament-bone composite scaffolds to repair the ligaments, to explore the fabrication method for ligament-bone composite scaffolds based on three-dimensional (3-D) printing technique, and to investigate their mechanical and biological properties in animal experiments. MethodsThe model of bone scaffolds was designed using CAD software, and the corresponding negative mould was created by boolean operation. 3-D printing techinique was employed to fabricate resin mold. Ceramic bone scaffolds were obtained by casting the ceramic slurry in the resin mould and sintering the dried ceramics-resin composites. Ligament scaffolds were obtained by weaving degummed silk fibers, and then assembled with bone scaffolds and bone anchors. The resultant ligament-bone composite scaffolds were implanted into 10 porcine left anterior cruciate ligament rupture models at the age of 4 months. Mechanical testing and histological examination were performed at 3 months postoperatively, and natural anterior cruciate ligaments of the right sides served as control. ResultsBiomechanical testing showed that the natural anterior cruciate ligament of control group can withstand maximum tensile force of (1 384±181) N and dynamic creep of (0.74±0.21) mm, while the regenerated ligament-bone scaffolds of experimental group can withstand maximum tensile force of (370±103) N and dynamic creep of (1.48±0.49) mm, showing significant differences (t=11.617,P=0.000; t=-2.991,P=0.020). In experimental group, histological examination showed that new bone formed in bone scaffolds. A hierarchical transition structure regenerated between ligament-bone scaffolds and the host bones, which was similar to the structural organizations of natural ligament-bone interface. ConclusionLigament-bone composite scaffolds based on 3-D printing technique facilitates the regeneration of biomimetic ligament-bone interface. It is expected to achieve physical fixation between ligament grafts and host bone.
ObjectiveTo improve the poor mechanical strength of porous ceramic scaffold, an integrated method based on three-dimensional (3-D) printing technique is developed to incorporate the controlled double-channel porous structure into the polylactic acid/β-tricalcium phosphate (PLA/β-TCP) reinforced composite scaffolds (double-channel composite scaffold) to improve their tissue regeneration capability and the mechanical properties. MethodsThe designed double-channel structure inside the ceramic scaffold consisted of both primary and secondary micropipes, which parallel but un-connected. The set of primary channels was used for cell ingrowth, while the set of secondary channels was used for the PLA perfusion. Integration technology of 3-D printing technique and gel-casting was firstly used to fabricate the double-channel ceramic scaffolds. PLA/β-TCP composite scaffolds were obtained by the polymer gravity perfusion process to pour PLA solution into the double-channel ceramic scaffolds through the secondary channel set. Microscope, porosity, and mechanical experiments for the standard samples were used to evaluate the composite properties. The ceramic scaffold with only the primary channel (single-channel scaffold) was also prepared as a control. ResultsMorphology observation results showed that there was no PLA inside the primary channels of the double-channel composite scaffolds but a dense interface layer between PLA and β-TCP obviously formed on the inner wall of the secondary channels by the PLA penetration during the perfusion process. Finite element simulation found that the compressive strength of the double-channel composite scaffold was less than that of the single-channel scaffold; however, mechanical tests found that the maximum compressive strength of the double-channel composite scaffold[(21.25±1.15) MPa] was higher than that of the single-channel scaffold[(9.76±0.64) MPa]. ConclusionThe double-channel composite scaffolds fabricated by 3-D printing technique have controlled complex micropipes and can significantly enhance mechanical properties, which is a promising strategy to solve the contradiction of strength and high-porosity of the ceramic scaffolds for the bone tissue engineering application.
ObjectiveTo explore the effectiveness of excision and reconstruction of bone tumor by using operation guide plate made by variety of three-dimensional (3-D) printing techniques, and to compare the advantages and disadvantages of different 3-D printing techniques in the manufacture and application of operation guide plate. MethodsBetween September 2012 and January 2014, 31 patients with bone tumor underwent excision and reconstruction of bone tumor by using operation guide plate. There were 19 males and 12 females, aged 6-67 years (median, 23 years). The disease duration ranged from 15 days to 12 months (median, 2 months). There were 13 cases of malignant tumor and 18 cases of benign tumor. The tumor located in the femur (9 cases), the spine (7 cases), the tibia (6 cases), the pelvis (5 cases), the humerus (3 cases), and the fibula (1 case). Four kinds of 3-D printing technique were used in processing operation guide plate:fused deposition modeling (FDM) in 9 cases, stereo lithography appearance (SLA) in 14 cases, 3-D printing technique in 5 cases, and selective laser sintering (SLS) in 3 cases; the materials included ABS resin, photosensitive resin, plaster, and aluminum alloy, respectively. Before operation, all patients underwent thin layer CT scanning (0.625 mm) in addition to conventional imaging. The data were collected for tumor resection design, and operation guide plate was designed on the basis of excision plan. Preoperatively, the operation guide plates were made by 3-D printing equipment. After sterilization, the guide plates were used for excision and reconstruction of bone tumor. The time of plates processing cycle was recorded to analyse the efficiency of 4 kinds of 3-D printing techniques. The time for design and operation and intraoperative fluoroscopy frequency were recorded. Twenty-eight patients underwent similar operations during the same period as the control group. ResultsThe processing time of operation guide plate was (19.3±6.5) hours in FDM, (5.2±1.3) hours in SLA, (8.6±1.9) hours in 3-D printing technique, and (51.7±12.9) hours in SLS. The preoperative design and operation guide plate were successfully made, which was used for excision and reconstruction of bone tumor in 31 cases. Except 3 failures (operation guide plate fracture), the resection and reconstruction operations followed the preoperative design in the other 28 cases. The patients had longer design time, shorter operation time, and less fluoroscopy frequency than the patients of the control group, showing significant differences (P<0.05). The follow-up time was 1-12 months (mean, 3.7 months). Postoperative X-ray and CT showed complete tumor resection and stable reconstruction. Conclusion3-D printing operation guide plates are well adapted to the requirements of individual operation for bone tumor resection and reconstruction. The 4 kinds of 3-D printing techniques have their own advantages and should be chosen according to the need of operation.
ObjectiveTo investigate the application of three-dimensional (3-D) printing technique combining with 3-D CT and computer aided-design technique in customized artificial bone fabrication, correcting mandibular asymmetry deformity after mandibular angle ostectomy. MethodsBetween April 2011 and June 2013, 23 female patients with mandibular asymmetry deformity after mandibular angle ostectomy were treated. The mean age was 27 years (range, 22-34 years). The disease duration of mandibular asymmetry deformity was 6-16 months (mean, 12 months). According to the CT data and individualized mandibular angle was simulated based on mirror theory, 3-D printed implants were fabricated as the standard reference for manufacturers to fabricated artificial bone graft, and then mandible repair operation was performed utilizing the customized artificial bone to improve mandibular asymmetry. ResultsThe operation time varied from 40 to 60 minutes (mean, 50 minutes). Primary healing of incisions was obtained in all patients; no infection, hematoma, and difficulty in opening mouth occurred. All 23 patients were followed up 3-10 months (mean, 6.7 months). After operation, all patients obtained satisfactory facial and mandibular symmetry. 3-D CT reconstructive examination results after 3 months of operation showed good integration of the artificial bone. Conclusion3-D printing technique combined with 3-D CT and computer aided design technique can be a viable alternative to the approach of maxillofacial defects repair after mandibular angle ostectomy, which provides a accurate and easy way.
ObjectiveTo establish a method to prefabricate titanium plate with three-dimensional (3-D) printing technique for correction of mandibular prognathism in sagittal splint ramous osteotomy (SSRO). MethodsBetween January 2012 and May 2013, 12 patients with mandibular prognathism (Angle III malocclusion) were treated. Among them, 9 cases were male and 3 cases were female. Their ages ranged from 19 to 35 years (mean, 25.6 years). With the 3-D facial CT data of these patients, 3-D printer was used to print the models for preoperational simulation. SSRO was performed on 3-D models, and the titanium plates were prefabricated on the models after the distal segments were moved backward and rotated according to occlusal splint. During operations, the proximal segments were fixed to distal segments by the prefabricated titanium plates. 3-D CT scans were taken to examine the temporomandibular joint position changes before operation and at 6 months after operation. ResultsThe skull models were manufactured by 3-D printing technique, and the titanium plates were reshaped on the basis of them. Twenty-four prefabricated titanium plates were placed during operations, and they all matched with the bone segments well. Evaluation of 3-D CT scans showed that the temporomandibular joint position had no change. All patients were followed up 7-12 months (mean, 10.6 months). The face type and dental articulation were improved greatly. All cases obtained satisfactory opening function and occlusion. ConclusionWith the titanium plate fabricated based on 3-D models, surgeons are able to improve or refine surgical planning so that the operation can be performed according to preoperative simulation precisely and the complications, such as dislocation of temporomandibular joint, can be prevented.
ObjectiveTo explore the application of three-dimensional (3-D) printing technique in repair and reconstruction of maxillofacial bone defect. MethodsThe related literature on the recent advance in the application of 3-D printing technique for repair and reconstructing maxillofacial bone defect was reviewed and summarized in the following aspects:3-D models for teaching, preoperative planning, and practicing; surgical templates for accurate positioning during operation; individual implantable prosthetics for repair and reconstructing the maxillofacial bone defect. Results3-D printing technique is profoundly affecting the treatment level in repair and reconstruction of maxillofacial bone defect. Conclusion3-D printing technique will promote the development of the repair and reconstructing maxillofacial bone defect toward more accurate, personalized, and safer surgery.