ObjectiveTo investigate the short-term effectiveness of total knee arthroplasty (TKA) assisted by three-dimensional (3D) printing osteotomy navigation template.MethodsA retrospective study was performed on 60 patients with osteoarthritis bewteen January 2016 and June 2017. Thirty cases underwent TKA assisted by 3D printing osteotomy navigation template (3D printing group) and 30 cases underwent the conventional TKA (conventional TKA group). There was no significant difference in gender, age, body mass index, surgical side, and disease duration between 2 groups (P>0.05). The operation time, the pre- and post-operative hemoglobin values, the amount of drainage, the Hospital for Special Surgery (HSS) score and Knee Society Score (KSS) of knee joint before operation and at 3 months after operation were observed. And 6 freedom degrees of knee (the varus and valgus angle, the internal and external rotation angle, the antero-posterior displacement, the proximal-distal displacement, the flexion and extension angle, and the internal and external displacement) before operation and at 3 months after operation were recorded by Opti-Knee (the knee 3D motion analysis system). The values of 2 groups were compared with 30 healthy adults (<60 years).ResultsThe operation time was shorter in 3D printing group than that in conventional TKA group (t=5.833, P=0.000). The hemoglobin values at 1 and 3 days after operation were higher in 3D printing group than those in conventional TKA group (P<0.05). The amount of drainage was less in 3D printing group than that in conventional TKA group (t=5.468, P=0.000). All patients were followed up 6-9 months (mean, 7.3 months). There was no significant difference in pre- and post-operative HSS score and KSS clinical score between 2 groups (P>0.05). There was no significant difference in preoperative KSS function score between 2 groups (P>0.05), but the KSS function score of 3D printing group at 3 months after operation was higher than that of conventional TKA group (P<0.05). Before operation, the varus and valgus angle, the internal and external rotation angle, the antero-posterior displacement, the proximal-distal displacement of 3D printing group and conventional TKA group were larger than that of the healthy adults (P<0.05); there was no significant difference in the flexion and extension angle and the internal and external displacement between 2 groups and healthy adults (P>0.05). At 3 months after operation, compared with healthy adults, the varus and valgus angle of conventional TKA group was increased, the flexion and extension angle of conventional TKA group was decreased (P<0.05); the proximal-distal displacement and the internal and external displacement of 2 groups were decreased (P<0.05); there was no significant difference in other freedom degrees between groups (P>0.05). No sign of prosthesis loosening was observed by X-ray examination.ConclusionCompared with the traditional TKA, TKA assisted by the 3D printing osteotomy navigation template had such advantages as shorter operation time, less postoperative blood loss, and well postoperative recovery.
ObjectiveTo explore the effectiveness and advantage of three-dimensional (3D) printed navigation templates assisted Ludloff osteotomy in treatment of moderate and severe hallux valgus.MethodsBetween April 2013 and February 2015, 28 patients (28 feet) with moderate and severe hallux valgus who underwent Ludloff osteotomy were randomly divided into 2 groups (n=14). In group A, the patients were treated with Ludloff osteotomy assissted with a 3D printed navigation template. In group B, the patients were treated with traditional Ludloff osteotomy. There was no significant difference in gender, age, affected side, and clinical classification between 2 groups (P>0.05). The operation time and intraoperative blood loss were recorded. The ankle function of the foot at preoperation, immediate after operation, and last follow-up were assessed by the American Orthopedic Foot and Ankle Society (AOFAS) score. Besides, the X-ray film were taken to assess the hallux valgus angle (HVA), intermetatarsal angle (IMA), and the first metatarsal length shortening.ResultsAll patients were followed up 18-40 months (mean, 26.4 months). The operation time and intraoperative blood loss in group A were significantly less than those in group B (P<0.05). The HVA, IMA, and AOFAS scores in groups A and B at immediate after operaton and last follow-up were sinificantly improved when compared with preoperative values (P<0.05); but no significant difference was found between at immediate after operation and at last follow-up (P>0.05). No significant difference was found in HVA and IMA between group A and group B at difference time points (P>0.05). There were significant differences in AOFAS score and the first metatarsal length shortening at immediate after operation and at last follow-up between 2 groups (P<0.05). Except 1 case of metastatic metatarsalgia in group B, there was no other operative complications in both groups.Conclusion3D printed navigation template assisted Ludloff osteotomy can provide accurate preoperative planning and intraoperative osteotomy. It is an ideal method for moderate and severe hallux valgus.
ObjectiveTo explore the gait trajectory characteristics of patients after total knee arthroplasty (TKA) assisted by three-dimensional (3D) printing navigation template.MethodsTwenty female patients (20 knees) with knee osteoarthritis who were treated with TKA assisted by 3D printing navigation template between February 2017 and February 2018 were selected as the 3D printing group. The patients were 50-69 years old, with an average age of 57.2 years. The disease duration was 4-7 years, with an average of 5.6 years. The osteoarthritis was classified as Kellgren-Lawrence Ⅲ level in 5 cases and Ⅳ level in 15 cases. The preoperative hip-knee-ankle angle (HKA) was (170.8±5.6)°. All patients were varus deformity. According to age and affected side, 20 healthy female volunteers were selected as the control group. The volunteers were 51-70 years old, with an average age of 56.7 years. Preoperative HKA was (178.8±0.6)°. There was significant difference in HKA between the two groups (P>0.05). The HKA, Western Ontario and McMaster University Osteoarthritis Index (WOMAC), and visual analogue scale (VAS) scores of the 3D printing group before and after operation were compared. At 6 months after operation, the gait trajectory characteristics of 3D printing group and control group were analyzed by Vicon gait capture system. The kinematics parameters included velocity, cadence, stride length, maximum knee flexion angle (stance), minimum knee flexion angle (stance), maximum knee flexion angle (swing), mean hip rotation angle (stance), mean ankle rotation angle (stance).ResultsThe incisions of 3D printing group healed by first intention, with no complications. All patients were followed up 7-12 months (mean, 9.0 months). The WOMAC and VAS scores at 6 months after operation were significant lower than those before operation (P<0.05). The HKA was (178.8±0.8)° at 4 weeks after operation and the difference was significant when compared with that before operation (t=39.203, P=0.000). The position of the prosthesis was good. The femoral posterior condyle osteotomy line, surgical transepicondylar axis, and patella transverse line were parallel, varus deformity was corrected, and lower limb alignment was restored to neutral position. Gait analysis at 6 months after operation showed that the differences in all kinematics parameters between the two groups were significant (P<0.05).ConclusionAssisted by 3D printing navigation template, TKA can alleviate pain symptoms and correct deformity, with satisfactory early effectiveness. Compared with healthy people, the early postoperative gait of the patients were characterized by decreasing velocity, cadence, stride length, knee flexion range, and increasing compensatory hip and ankle rotation range.
ObjectiveTo investigate the effectiveness of three-dimensional (3D) navigation template in the adult cubitus varus osteotomy.MethodsBetween April 2013 and September 2015, 17 patients with cubitus varus were admitted. There were 6 males and 11 females, aged from 19 to 38 years, with an average age of 26.9 years. There were 10 cases of left elbow joints and 7 cases of right elbow joints. The disease duration was 9-30 years (mean, 18 years). Based on the preoperative X-ray film, the humerus-elbow-wrist (HEW) angle was (−13.2 ±3.3)°, the anteversion angle was (−10.5±2.3)°. The preoperative range of motion (ROM) of flexion was (127.3±7.3)° and ROM of extension was (−10.0±2.5)°. Based on the CT 3D reconstruction, the osteotomy navigation template was designed and printed by 3D printing technique. The cubitus varus osteotomy was assisted by 3D navigation template. The postoperative HEW angle, anteversion angle, and ROMs of the elbow joints of both sides were measured. The elbow function was evaluated based on the Oppenheim elbow function score at 1 year after operation.ResultsAll cubitus varus osteotomies succeeded with the assist of 3D navigation template. All incisions healed by first intention. All patients were followed up 12-15 months (mean, 13 months). X-ray films showed that all osteotomies healed after 9-12 weeks (mean, 11 weeks). At 1 year after operation, the HEW angle was (9.7±1.9)°, the anteversion angle was (20.7±4.3)°, the ROM was (2.6±3.5)° in extension and (139.2±4.8)° in flexion of affected side. The HEW angle, anteversion angle, and ROMs significantly increased compared with preoperative values (P<0.05). And there was no significant difference between affected and normal elbow joints (P>0.05). The elbow functions were excellent in 13 cases and good in 4 cases based on the Oppenheim elbow function score at 1 year after operation. There was no complication such as the nerve injury or osteomyositis of elbow joint during follow-up. ConclusionThe 3D navigation template can provide a personalized and precise osteotomy treatment for adult cubitus varus deformity and obtain a satisfactory effectiveness.
ObjectiveTo explore the effectiveness of a new point contact pedicle navigation template (referred to as “new navigation template” for simplicity) in assisting screw implantation in scoliosis correction surgery. MethodsTwenty-five patients with scoliosis, who met the selection criteria between February 2020 and February 2023, were selected as the trial group. During the scoliosis correction surgery, the three-dimensional printed new navigation template was used to assist in screw implantation. Fifty patients who had undergone screw implantation with traditional free-hand implantation technique between February 2019 and February 2023 were matched according to the inclusion and exclusion criteria as the control group. There was no significant difference between the two groups (P>0.05) in terms of gender, age, disease duration, Cobb angle on the coronal plane of the main curve, Cobb angle at the Bending position of the main curve, the position of the apical vertebrae of the main curve, and the number of vertebrae with the pedicle diameter lower than 50%/75% of the national average, and the number of patients whose apical vertebrae rotation exceeded 40°. The number of fused vertebrae, the number of pedicle screws, the time of pedicle screw implantation, implant bleeding, fluoroscopy frequency, and manual diversion frequency were compared between the two groups. The occurrence of implant complications was observed. Based on the X-ray films at 2 weeks after operation, the pedicle screw grading was recorded, the accuracy of the implant and the main curvature correction rate were calculated. ResultsBoth groups successfully completed the surgeries. Among them, the trial group implanted 267 screws and fused 177 vertebrae; the control group implanted 523 screws and fused 358 vertebrae. There was no significant difference between the two groups (P>0.05) in terms of the number of fused vertebrae, the number of pedicle screws, the pedicle screw grading and accuracy, and the main curvature correction rate. However, the time of pedicle screw implantation, implant bleeding, fluoroscopy frequency, and manual diversion frequency were significantly lower in trial group than in control group (P<0.05). There was no complications related to screws implantation during or after operation in the two groups. ConclusionThe new navigation template is suitable for all kinds of deformed vertebral lamina and articular process, which not only improves the accuracy of screw implantation, but also reduces the difficulty of operation, shortens the operation time, and reduces intraoperative bleeding.