This paper is to report our study in which the differences between prosthetic restoration and surgical reconstruction using traditional clasp retention technology were analyzed based on three-dimensional finite element methods in our laboratory. Firstly, the maxillary unilateral defect model was developed using medical image processing software MIMICS. Secondly, the prosthesis was generated by mirroring technology. The clasp was designed according to the methods raised by Aramany. Then, the stress distribution of maxilla was calculated by simulating occlusion. According to the results, after osseointegration of surgical reconstruction, stresses of unaffected abutments were reduced significantly, and less stress of junction occurred near zygoma of affected side, which were all less than stresses of prosthesis restoration. Thus, removing the clasp of surgical reconstruction increased the stresses of unaffected abutments. The stress trends of maxillary components were different between prosthetic restoration and surgical reconstruction. Surgical reconstruction is better than prosthesis restoration in protection of the abutments. Clasp can alleviate the occlusal burden of maxilla. Varieties of retentive technologies can be considered in prosthesis restoration. The surgical reconstruction is more conducive to rehabilitate unilateral maxilla biomechanically in clinic.
Foam sclerotherapy is one of the major therapies for varicose veins in lower limbs. It is important to know the influence factor of foam stability which is beneficial to curative effect. The present experiment explored influence of 9 kinds of driving speed on foam stability when using the method of Tessari. Syringes of 5 mL were chosen to do this experiment which was carried out at the liquid gas ratio of 1:4 and the environment temperature of 20℃. A home-made automatic sclerosing foam preparation equipment was used to prepare the foam. A camera recorded the entire process of foam decay. And foam stability indexes which includes drainage time, half-life, foam half-life volume and the drainage rate curve, were analyzed. The results showed that when driving speed ranged from 100 mm/s to 275 mm/s, foam drainage time and the half-life showed a trend of rising. When the driving velocity was greater than 275 mm/s, the foam drainage time and half-life time reduced a little. The largest drainage time and the half-life differences were 340.0% and 118.8% compared to their minimum value. Meanwhile the pressure increased with the increase of driving speed, so that the solubility of carbon dioxide increased and the foam half-life volume decreased with the increase of the driving speed. It can be concluded that when using the method of Tessari to prepare sclerosing foam, driving speed has a significant effect on its stability. With driving speed increasing, foam decay mechanism changes from gas diffusion to liquid drainage as the main function, so the foam stability increased at first and then decreased later. The foam is relatively more stable at the speed of 275 mm/s, which could be considered as the best driving speed.
Polydimethylsiloxane (PDMS) and hydroxyapatite (HA) were combined in our laboratory to fabricate an elastic porous cell scaffold with pore-forming agent, and then the scaffold was used as culture media for rat bone marrow derived mesenchymal stem cells (rBMSCs). Different porous materials (square and circular in shape) were prepared by different pore-forming agents (NaCl or paraffin spheres) with adjustable porosity (62%-76%). The HA crystals grew on the wall of hole when the material was exposed to SBF solutions, showing its biocompatibility and ability to support the cells to attach on the materials.
This study was aimed to estimate the effect of different ProDisc-C arthroplasty designs after it was implanted to C5-C6 cervicalspine. Finite element (FE) model of intact C5-C6 segments including the vertebrae and disc was developed and validated. Ball-and-socket artificial disc prosthesis model (ProDisc-C, Synthes) was implanted into the validated FE model and the curvature of the ProDisc-C prosthesis was varied. All models were loaded with compressed force 74 N and the pure moment of 1.8 Nm along flexion-extension and bilateral bending and axial torsion separately. The results indicated that the variation in the curvature of ball and socket configuration would influence the range of motion in flexion/extension, while there were not apparently differences under other conditions of loads. The method increasing the curvature will solve the stress concentration of the polyethylene, but it will also bring adverse outcomes, such as facet joint force increasing and ligament tension increasing. Therefore, the design of artificial discs should be considered comprehensively to reserve the range of motion as well as to avoid the adverse problems, so as not to affect the long-term clinical results.
This study investigated the effect of prolonged walking with load carriage on body posture, muscle fatigue, heart rate and blood pressure of the tested subjects. Ten healthy volunteers performed 30 min walking trials on treadmill (speed=1.1 m/s) with different backpack loads [0% body weight (BW), 10%BW, 15%BW and 20%BW]. The change of body posture, muscle fatigue, heart rate and blood pressure before and after walking and the recovery of muscle fatigue during the rest time (0, 5, 10 and 15 min) were collected using the Bortec AMT-8 and the NDI Optotrak Certus. Results showed that the forward trunk and head angle, muscle fatigue, heart rate and blood pressure increased with the increasing backpack loads and bearing time. With the 20%BW load, the forward angle, muscle fatigue and systolic pressure were significantly higher than with lighter weights. No significantly increased heart rate and diastolic pressure were found. Decreased muscle fatigue was found after removing the backpack in each load trial. But the recovery of the person with 20%BW load was slower than that of 0%BW,10%BW and 15%BW. These findings indicated that the upper limit of backpack loads for college-aged students should be between 15% BW and 20%BW according to muscle fatigue and forward angle. It is suggested that backpack loads should be restricted to no more than 15%BW for walks of up to 30 min duration to avoid irreversible muscle fatigue.
We observed the effect of vibration parameters on lumbar spine under different vibration conditions using finite element analysis method in our laboratory. In this study, the CT-images of L1-L5 segments were obtained. All images were used to develop 3D geometrical model using the Mimics10.01 (Materialise, Belgium). Then it was modified using Geomagic Studio12.0 (Raindrop Geomagic Inc. USA). Finite element (FE) mesh model was generated by Hypermesh11.0 (Altair Engineering, Inc. USA) and Abaqus. Abaqus was used to calculate the stress distribution of L1-L5 under different vibration conditions. It was found that in a vibration cycle, tensile stress was occurred on lumbar vertebra mainly. Stress distributed evenly and stress concentration occurred on the left rear side of the upper endplate. The stress had no obvious changes under different frequencies, but the stress was higher when amplitude was greater. In conclusion, frequency and amplitude parameters have little effect on the stress distribution in vertebra. The stress magnitude is positively correlated with the amplitude.