ObjectiveTo summarize and analyze the application of ex vivo liver resection and autotransplantation (ELRA) in the treatment of hepatobiliary diseases. MethodThe related literature about ELRA used to treat various hepatobiliary space-occupyingdiseases at home and abroad in recent years was comprehensively searched and summarized. ResultsELRA had overcome the limitations of limited operational space in traditional surgery for the treatment of hepatobiliary space-occupying diseases reduced dependence on donor livers, and avoided post-transplant rejection. It had been applied in the treatment of hepatic alveolar echinococcosis, liver cancer, cholangiocarcinoma, and rare liver space-occupying diseases. ConclusionsWith the maturation of ELRA techniques and the continuous improvement of ex vivo liver perfusion technology, along with rigorous preoperative evaluation and meticulous postoperative management, postoperative complications of ELRA have significantly decreased compared to the initial stages of its application. By strictly adhering to surgical indications, this procedure is expected to be used treatment in an increasing number of hepatobiliary space-occupying diseases.
Objective To summarize the nutritional assessment methods for liver cancer patients and their development, and to provide reference for rationally nutritional assessment and nutritional support. Method Domestic and foreign literatures were searched to summarize the nutritional assessment methods for liver cancer patients and their development, in order to determine a practical and feasible assessment method. Results The evaluation validity of traditionally nutritional assessment methods which contained many individual indicators was low. But subjective global assessment (SGA), mini nutritional assessment (MNA), and nutritional risk screening 2002 (NRS-2002) had similar evaluation validity, this 3 kinds of nutritional assessment methods were more suitable for liver cancer patients compared with the traditionally nutritional assessment methods. Conclusion The clinician should simultaneously apply SGA, MNA, NRS-2002, and other comprehensively nutritional assessment methods, as well as related anthropometric and laboratory indexes, to get a more accurate assessment of the nutritional status for patients with liver cancer.
ObjectiveTo investigate the effectiveness of three-dimensional (3D) printed total scapula for reverse shoulder arthroplasty in the treatment of scapular tumors. MethodsBetween November 2017 and December 2021, 5 patients with scapular tumors were treated by reverse shoulder arthroplasty with 3D printed total scapula. There was 1 male and 4 females. The age ranged from 44 to 59 years, with an average of 50.4 years. There were 2 cases of chondro sarcoma, 1 case of high-grade osteosarcoma, 1 case of lung cancer with scapular metastasis, and 1 case of ligamentoid fibromatosis recurrence. The disease duration was 4-8 months, with an average of 5.8 months. According to the Musculoskeletal Tumor Society (MSTS) scapular girdle classification criteria, 4 cases of tumors involved both S1 and S2 zones, and 1 case involved S2 zone. The tumor diameters ranged from 4.2 to 11.2 cm, with an average of 6.1 cm. The operation time, intraoperative blood loss, and blood transfusion were recorded. During follow-up, the MSTS score was used to evaluate the recovery of limb function of the patients. The sink depth of the affected shoulder, complications, and oncological outcomes were observed. The position of the prosthesis was reviewed by imaging. ResultsThe operation time ranged from 155 to 230 minutes, with an average of 189 minutes. The intraoperative blood loss was 100-1 500 mL, with a median of 600 mL. Two patients were received blood transfusion of 800 mL and 1 850 mL respectively during operation. All incisions healed by first intention, and no complications such as infection occurred. All patients were followed up 4-22 months, with an average of 13 months. Two patients died at 8 and 15 months after operation respectively due to multiple metastases and organ failure. At last follow-up, the MSTS score of all patients was 73%-83%, with an average of 77.4%. The affected shoulder was 2-4 cm lower than the contralateral side, with an average of 3 cm. Imaging examinations showed that no prosthesis loosening, dislocation, or fracture occurred during follow-up. Conclusion Reverse shoulder arthroplasty with 3D printed total scapula can obtain good shoulder function and appearance. Patients have high acceptance and satisfaction with this surgical method.